One Blow. One Connection.
SlimRun Jet — The aerodynamic LC ferrule engineered for micro-duct jetting. Deploy hundreds of meters through 3.5 mm ducts in a single operation, then terminate without field polishing or splicing.
LC Only
1.0–1.2 mm Jetting Cable
>100N Tensile
Main Features
Glides Through 3.5 mm Ducts
The specialized bullet shape maintains laminar airflow during high-pressure jetting operations. Unlike standard assemblies that tumble and jam, the slim, short, flexible profile passes through 3.5 mm ID micro-ducts for distances that exceed traditional limits — no midway access points, no intermediate splices.
Factory-Clean, Field-Ready
Even after high-speed transit through dusty micro-ducts, the protective cap remains sealed until final housing assembly. Remove the aerodynamic sleeve, fit the outer housing, and the ferrule is still factory-polished — guaranteeing ≤0.3 dB insertion loss without field polishing.
Built for the Blow
The 1.2 mm jetting cable and reinforced construction withstand >100N tensile force during deployment. The assembly handles air pressure, friction, and 90° bends without compromising the factory-polished ferrule inside. Long-term tensile rating: 18N–30N depending on cable.
Blow and Terminate
Blow directly from the distribution point to the apartment entry in a single pass. The SlimRun Jet installs as a complete factory-terminated assembly — no bare fiber to blow and then field-terminate separately. Eliminates the separate blow-and-splice operation.
Technical Specifications.
| Parameter | Specification |
|---|---|
| Connector Type | LC only |
| Ferrule Design | Aerodynamic bullet profile with sealed protective cap |
| Compatible Cables | 1.2 mm round jetting cable |
| Compatible Micro-Ducts | 5/3.5 mm, 7/5.5 mm |
| Installation Method | Micro-duct jetting |
| Insertion Loss (Typical) | ≤0.25 dB (Premium), ≤0.15 dB (Low Loss) |
| Insertion Loss (Max) | 0.30 dB (Premium), 0.20 dB (Low Loss) |
| Return Loss | ≥50 dB (UPC), ≥65 dB (APC) |
| Tensile Strength (Jetting) | >100N (IEC 60794-1-E1) |
| Tensile Strength (Long-term) | 18N–30N (IEC 60794-1-E1) |
| Performance Under Load | 40N/60s (IEC 61300-2-4) |
| Operating Temperature | -40°C to +80°C |
| Bending Radius (Static) | 20× cable diameter |
| Bending Radius (Dynamic) | 10× cable diameter |
| Fiber Type | Single-mode (G.657.A1/A2 compatible) |
Deployment Scenarios
FTTR, No Compromise
In fiber-to-the-room deployments, blow SlimRun Jet assemblies through pre-installed 5/3.5 mm micro-ducts from the building distribution point directly to each apartment. No hallway trays, no riser cables — just clean, invisible infrastructure that terminates at the optical network terminal without additional splices.
One Action. No Home Entry.
Traditional pull/push deployment is two actions: first pull a guide wire through the duct, then pull the fiber through — requiring technician access to the apartment or house. Jetting changes the equation. One high-pressure blow sends the SlimRun Jet directly to the subscriber wall box. The pressure drop confirms arrival. No door knocking. No appointment scheduling. Termination is simple enough for the subscriber, the ISP modem installer, or a follow-up visit — but the hard part is already done.
Invisible Infrastructure
Luxury apartments and historic buildings where aesthetic standards prohibit surface raceways and structural limits prevent new conduit installation. Blow SlimRun Jet through the smallest available pathways — 3.5 mm ID micro-ducts embedded in walls or under floorboards — delivering fiber connectivity with minimal structural impact.
Standards Alignment.
Blow Through. Terminate. Done.
Request a SlimRun Jet evaluation kit with LC variants, 1.2 mm jetting cable samples, and blowing compatibility guidelines. Our application engineers will validate duct specifications for your specific FTTH infrastructure.